上海凱賢印刷科技有限公司為您提供烤漆面自干五金油墨。
本產品主要用于各種金屬、玻璃、真空電鍍、水電鍍、電泳、陽極氧化鋁、電解板、鋁塑板、噴塑、噴粉、靜電噴漆面、烤漆面以及各種天花吊頂氧化板、鏡面板、覆膜板、輥涂板、尼龍加玻纖、三聚--胺板,uv表面,木板烤漆面等等制品的絲印及移印。
2、產品特性:亮光、附著力佳、快干、耐沖壓。
3、稀釋劑:用我司b-03-稀釋劑或783開油,用718洗網水清洗網版。
4、固化劑:?jiǎn)谓M份使用,也可選擇添-司js-10-固化劑用于增加油墨附著力及物理化學抗性。
5、油墨調配方法:開罐先攪拌均勻,取所需量油墨稀釋到合適印刷粘度。如需添加固化劑,先加固化劑攪拌后靜置10分鐘,待油墨與固化劑完全交聯后再進行稀釋。
6、干燥時間:常溫干燥,表干時間5-10分鐘,實干時間在24小時以內,80℃烘烤20分鐘可快速干燥。
7、添加固化劑后的使用時限:4-6小時,過期請棄用,剩余油墨不可回收。
性能檢測
1、3m膠帶劃百格測試:100%無脫落
2、耐沖壓測試:1mm厚鋁板180°折彎無變化。
3、耐酒精測試:用脫脂棉沾濃度99%工業酒精以500g力水平來回200次無脫色。
注意事項
1、先小量試印確認符合要求后再批量生產。
2、做好承印物的表面清除油脂及雜質工作,以促進附著效果。
3、附著力、硬度、耐酸性、耐酒精性、耐化學品性、抗劃傷性、耐磨性等性能的檢測,
需要完全固化后方可檢測。
4、未經允許情況下,不得將本系列油墨與其它類型油墨混用及配色。
5、油墨,稀釋劑使用及儲存時嚴-火。
6、使用時注意施工場所的通風狀況-,盡量避免皮膚直接接觸。
7、本品不慎濺入口、鼻、眼、耳內,應用大量水清洗或直接求助醫生。
8、技術參考數見下表:
檢驗項目 檢驗結果 測試條件
油墨線度 ≤12um 刮板細度計
干膜光澤 ***65° 60°鏡面光澤計
干燥速度 表干 25℃×5-10min 或60℃×2-3min
實干 25℃12hr或60℃×10min
耐酒精性 無變化 500克力/cm2酒精棉200次來回
附著力 100/100 1mm×1mm×100格3m膠紙剝離
耐酸性 無變化 浸泡5%hci×24hr
耐堿性 無變化 浸泡5%naoh×24hr
耐鹽性 無變化 浸泡5%naci×24hr
耐水性 無變化 浸泡20℃自來水×96hr
耐磨性 不見底 500克/cm2負載含砂橡皮200來回
耐熱性 無變化 80℃×12hr
the products are mainly used in screen printing&the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint surface&various ceiling oxide board, mirror panels, coated board, roller coated board&other products.
2, product characteristics: light, good adhesion, fast drying, stamping resistance.
3, diluent: with our b-03 spe-l thinner/783 open oil, washing network water cleaning screen with 718.
4, curing agent: one component use, can also choose to add our js-10 spe-l curing agent is used to increase the ink adhesion&physical&chemical resistance.
5, printing ink allocation methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity. if you need to add curing agent, first add curing agent after mixing&set aside for 10 minutes,&curing agent for ink completely crosslinking after dilution.
6, the drying time: dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly.
7, adding curing agent after the use of time: 4-6 hours, expired please abandoned, residual ink unrecyclable.
[detection] performance
1, 3m tape row adhesion test: 100% without shedding
2, stamping resistance test: 1mm thick aluminum 180 degree bend without change.
3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500g stress level&back 200 times without decolorization.
[note]
1, the first small try printing again after confirmation of compliance with the requirements of mass production.
2, do a good job in the substrate surface to remove grease&impurities, in order to promote the adhesion effect.
detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scr-h resistance, abrasion resistance&other properties,
fully cured before detection.
4, without permission, may not use the series of ink&other types of ink mixing&m-hing.
5, ink, fireworks is strictly prohibited the use of thinner&storage.
6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin.
7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing/direct help doctor.
本公司主營:
pp免處理油墨
-
自干金屬油墨
-
免烘烤金屬自干油墨
-
高溫鋼化玻璃油墨
-
uv絲印移印油墨
本文鏈接:
http://jiewangda.cn/gongying/94644492.html
聯系我們時請一定說明是在100招商網上看到的此信息,謝謝!
聯系電話:15900568152,021-59507952,歡迎您的來電咨詢!